Radiant Floor Heating Design — King City
In-floor and hydronic radiant design for King City, Nobleton, Schomberg and King Township — CSA F280 load, supply-water temperature, loop and manifold sizing, and boiler or air-to-water heat pump selection, all BCIN-stamped for the Township of King.
Radiant floor design for a King City permit is built on a CSA F280 heat loss calculation at the correct -21°C design temperature (Climate Zone 6 — King Township is colder than Toronto and the GTA at -18°C). We size supply-water temperature, loop spacing and manifolds to that load and select the boiler or air-to-water heat pump, BCIN-stamped for the Township of King. From $895.
King City design temperature: -21°C (Zone 6)
King Township — King City, Nobleton and Schomberg — is in Climate Zone 6 with an OBC January 2.5% design temperature of about -21°C from Supplementary Standard SB-1, colder than Toronto and the GTA (-18°C, Zone 5). Radiant slabs are unforgiving of an undersized load calculation, so the design must start from the correct -21°C value, not a GTA assumption. We confirm the SB-1 value for your site before sizing. Check yours with our free design temperature lookup.
What a King City radiant design includes
Every radiant package starts with a room-by-room CSA F280 heat loss calculation at -21°C, then the radiant-specific design: required supply-water temperature, loop length and tube spacing per zone, manifold layout and flow balancing, and selection of the heat source — a condensing boiler or an air-to-water heat pump — per CAN/CSA-B214. The package is BCIN-stamped for the Township of King Building Division and pairs with the MVDS ventilation summary and Schedule 1. See our radiant design service.
Heat source at -21°C: boiler or air-to-water heat pump
At King City -21°C, an air-to-water heat pump can run a low-temperature radiant slab efficiently for much of the season, but its output falls to roughly 65-75% of rated capacity on the design day — so it must be checked against the CSA F280 load, with a backup or boiler specified where needed. A condensing boiler is sized to the same load. The room-by-room calculation at -21°C is what determines the right supply temperature and heat source; see our cold climate heat pump guide.
Radiant Design in King City — FAQ
What design temperature is used for radiant design in King City?
-21°C (Climate Zone 6), the King Township OBC January 2.5% value from SB-1 — colder than Toronto and the GTA at -18°C. The CSA F280 load, supply-water temperature and loop sizing are all based on -21°C.
How much does a radiant floor design cost in King City?
A BCIN-stamped radiant design — CSA F280 load, supply temperature, loop and manifold sizing and heat-source selection — starts at $895. A standalone heat loss report starts at $395.
Can an air-to-water heat pump run my King City radiant floor?
Yes for well-insulated homes — radiant runs at low supply temperatures that suit heat pumps. At -21°C output falls to about 65-75% of rated, so we verify it against the CSA F280 load and specify backup or a boiler where appropriate.
Is the permit submitted to York Region or King Township?
To the Township of King Building Division. York Region does not issue residential building permits — each municipality runs its own building department.
Related Services & Areas
Building in King City? Radiant design done right.
Upload your plans and we confirm King Township SB-1 design temperature (-21°C, Zone 6), produce the BCIN-stamped CSA F280 and full radiant design, and format it for the Township of King.
See the ServiceGet a Free QuoteUpload your floor plans and we deliver a BCIN-stamped CSA F280 heat loss report from $395, or the complete HVAC permit package — mechanical drawings, MVDS, Schedule 1, BCIN stamp on every page — from $695. Delivered in 48 hours, accepted by every Ontario building department. Free quote within 24 hours, no obligation.
- CSA F280 at your municipality’s design temperature
- MVDS & Schedule 1 included
- BCIN stamp on every page
- 48-hour delivery, province-wide
- Free quote in 24 hours — or call 705-533-1633